 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SIDACtor (R) Protection Thyristors LCAS Protection Asymmetrical Discrete Series - DO-214 Description The Asymmetrical Discrete Series are SIDACtor(R) devices designed to protect LCAS (Line Circuit Access Switch) devices from damaging overvoltage transients. The series provides a specialized asymmetrical overvoltage protection solution that enables equipment to comply with various global requlatory standards. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Does not degrade with use Fails short circuit when surged in excess of ratings LCAS specific tip and ring thresholds Applicable Global Standards TIA-968-A TIA-968-B ITU K.20/21 Enhanced Level* ITU K.20/21 Basic Level GR 1089 Inter-building* *A/B-rated parts require series resistance Pinout Designation Not Applicable Schematic Symbol GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Electrical Characteristics VDRM @lDRM=5A V min P1200SALRP P2000SALRP P2500SALRP P1200SBLRP P2000SBLRP P2500SBLRP P1200SCLRP P2000SCLRP P2500SCLRP P12A P20A P25A P12B P20B P25B P12C P20C P25C 100 180 230 100 180 230 100 180 230 VS @100V/s V max 130 220 290 130 220 290 130 220 290 IH mA min 120 120 120 120 120 120 120 120 120 IS mA max 800 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 A V max 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF min pF max Part Number Marking 30 25 20 30 25 35 20 20 30 45 35 35 65 95 95 35 35 85 Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are bi-directional. (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 134 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors LCAS Protection Surge Ratings IPP 0.2x310 1 0.5x700 2 A min A B C Notes: 1 Current waveform in s 2 Voltage waveform in s - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40C < TJ < Series 2x10 1 2x10 2 A min 150 250 500 8x20 1 1.2x50 2 A min 150 250 400 10x160 1 10x160 2 A min 90 150 200 10x560 1 10x560 2 A min 50 100 150 5x320 1 9x720 2 A min 75 100 200 10x360 1 10x360 2 A min 75 125 175 10x1000 1 10x1000 2 A min 45 80 100 5x310 1 10x700 2 A min 75 100 200 ITSM 50/60 Hz A min 20 25 30 di/dt Amps/s max 500 500 500 20 25 50 Thermal Considerations Package DO-214AA Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 90 Value Unit C C C/W V-I Characteristics +I tr x td Pulse Waveform IPP - Peak Pulse Current - %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t - Time (s) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 14 2.0 Percent of VS Change - % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25C) 12 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 C 25C Ratio of Junction Temperature (TJ) - C (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 135 Revised: February 22, 2011 Case Temperature (TC) - C SIDACtor (R) Protection Thyristors LCAS Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) TP Ramp-up tP Critical Zone TL to TP 60-180 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) 3C/sec. Max. 60-150 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5C of actual Peak Temp (tp) Ramp-down Rate Time 25C to Peak Temp (TP) Do not exceed 30 secs. Max. 6C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25C to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking P xxx 0 S x L RP TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK RoHS COMPLIANT IPP RATING Pxxx xxxxx Part Marking Code (Refer to Electrical Characteristics Table) Date Code (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 136 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors LCAS Protection Dimensions -- DO-214AA Case Temperature Measurement Point CA 0.079 (2.0) Pad Outline 0.079 (2.0) B D Dimensions A Inches Min 0.130 0.201 0.077 0.159 0.030 0.075 0.002 0.077 0.006 Millimeters Min 3.30 5.10 1.95 4.05 0.75 1.90 0.05 1.95 0.15 Max 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 Max 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 0.110 (2.8) inch (millimeter) B C D E F G H H E F K G K Packing Options Package Type S Description DO-214AA Tape & Reel Pack Quantity 2500 Added Suffix RP Industry Standard EIA-481-D Tape and Reel Specification -- DO-214AA 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 12.99 (330.0) 0.059 DIA (1.5) Cover tape 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 137 Revised: February 22, 2011 |
Price & Availability of P1200SCLRP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |